Keeping CCTV Running During Load-Shedding: UPS, Inverters and PoE
Quick answer
A CCTV system that switches off during outages misses the moments that matter. Here is how to calculate power needs and choose backup.
By ITvein TeamPublished Updated 2 min read
Power outages are a fact of life in many parts of Pakistan, and intruders know it. A CCTV system without backup power can go dark exactly when it is needed. Planning backup is straightforward once you know your power load.
Step 1: Add up the power
Check the datasheets, but typical figures are:
| Device | Typical power |
|---|---|
| Fixed camera (IR on at night) | about 4–8 W |
| Pan-tilt / PTZ camera | about 10–30 W+ |
| 4/8-channel DVR or NVR (with HDD) | about 10–20 W |
| PoE NVR or PoE switch | its own use plus all PoE cameras |
| Internet router / ONT | about 6–15 W |
Example: 8 cameras × 6 W + recorder 15 W + router 10 W ≈ 73 W.
Step 2: Decide how long it must run
Typical load-shedding blocks are one to several hours. Decide the runtime you want, for example 2–4 hours, and plan for longer if outages are long in your area.
Step 3: Choose the backup method
Dedicated UPS for CCTV
- Simple and clean: recorder, router and camera power supply (or PoE switch) connected to a UPS.
- Runtime depends on battery capacity; small UPS units often give only 10–30 minutes at full load, while units with external batteries last longer.
Home inverter/UPS system
- If the house already has an inverter, put the CCTV circuit on it.
- Make sure the inverter's switchover is quick enough that the recorder doesn't restart. If it restarts on every outage, add a small online or line-interactive UPS just for the recorder.
Solar with batteries
- Increasingly common; works well when sized for night-time load.
DC power supply with battery backup
- For HD analog systems, a 12 V supply with battery backup can power cameras directly.
Step 4: Make PoE work for you
With IP cameras powered by a PoE NVR or PoE switch, you only need to back up one device (plus the router) to keep every camera running. See PoE explained and PoE switch buying guide.
Protect against surges and voltage swings
When power returns, spikes and low voltage can damage equipment. Use surge protection and a stabiliser where voltage is unstable. See surge and earthing protection.
Don't forget the internet
If the router and fibre/ONT box are not on backup, the cameras keep recording but you lose remote viewing and alerts during outages.
Testing
Switch off mains power for a few minutes and check:
- The recorder keeps running (no reboot).
- All cameras keep showing video, including at night.
- Remote viewing still works.
Frequently asked questions
How long will a UPS run my CCTV?
It depends on battery capacity and load. A 70–80 W system on a small UPS may only run for a short time; external batteries extend this to hours. Ask for a runtime estimate based on your actual load.
Is it bad if my DVR restarts every time the power goes?
Yes. Frequent sudden restarts can corrupt the hard drive and cause recording gaps. Put the recorder on a UPS that switches without interruption.
Do cameras use more power at night?
Yes. IR LEDs or white lights add to the power draw, so calculate with night-time figures.
Want advice for your own site?
Send photos and your requirements — we reply with an itemised quotation.
Products mentioned in this guide
Dahua
Dahua DH-CS4006-4ET2GT-36 6-Port Managed PoE Switch | 4 PoE, 2 Gigabit Uplink
In stock
PKR 8,650
Dahua
Dahua CS4010-8ET-60 10-Port Cloud Managed PoE Switch | 8 PoE Ports, 2 Uplink
In stock
PKR 15,050
Cisco
Cisco Catalyst 3560G-48p Switch – 48 ports – Managed Non PoE Switch
In stock
Price range PKR 40,000–60,000
Price confirmed on WhatsApp

